How To Take Window Out Of Car Door

Download Commodity

If i of the ability windows in your vehicle fails to office, it may be the result of a broken power window motor. If you accept identified the motor every bit the culprit, replacing it is fairly straight forward, though it can exist time consuming. It is recommended that yous review a service manual specific to your vehicle when replacing the motor, every bit the methods used to disassemble automobile doors tin vary from vehicle to vehicle.

1
Remove the interior door panel. Nearly interior door panels are held in identify with plastic interior fasteners. You can remove these fasteners by pulling on them until they popular out of their holes. Interior panels may also be held on with metallic or plastic screws or fifty-fifty bolts.^[one]
- If you can't easily identify what kind of fasteners are on your door panel, refer to the vehicle's service manual.
- Turn screws or bolts counter clockwise to loosen them, so pull the panel backward off of the door.
ii
Gently remove the plastic door comprehend. Below the door panel you will detect a sparse, translucent layer of plastic. This cover protects the interior of the vehicle from any water that may splash into the door from to a higher place and below. Carefully pull the door off of the sticky portions that secure it.^[2]
- Endeavour not to tear the cover as you will need to reinstall it after replacing the window motor.
- Replacement covers tin can exist purchased at your local auto parts store.
Ad
three
Locate the window mounting bolts. Depending on the design of your door, there are a few different places the window mounting bolts may exist, but it should be fairly apparent when looking into the door. Await for the bolts attaching the window itself to the mechanism that raises and lowers information technology.^[3]
- Y'all may demand to apply a flashlight to look into the service ports on the door.
- Different shaped doors volition identify the bolts in unlike locations.
iv
Movement the window if necessary to access the bolts. In some cases, you lot may demand to raise or lower the window in order to admission the bolts. Plough the key in the ignition of the vehicle without starting the engine to move the window if demand be.^[4]
- Heighten or lower the window using the power window buttons if possible.
- If the motor is cleaved, yous can force the window up or down by paw.
5
Remove the bolts while a friend supports the window. Utilize the appropriate sized socket or open concluded wrench to remove the window mounting bolts, but ask a friend to hold the window up every bit you do to prevent it from falling down once it's disconnected.^[five]
- Y'all may be able to agree the window in place as you loosen the bolts yourself, but it'southward dangerous.
- Dropping the window freely could result in the glass breaking.
vi
Heighten the window up into the door frame. Have your friend raise the window up into the door frame equally though you lot had rolled information technology upward normally. Ask them to hold the window in place until you are able to secure it.^[half-dozen]
- Pressing one palm on each side of the drinking glass will permit your friend to agree the window upwards.
7
Use masking tape to secure the window in place. With your friend holding the window upwards, pull off iii or four strips of masking tape that are each about a foot long. Stick the strips to the window on each side over the door frame to hold the window up while you work.^[7]
- In one case the window is secured with the tape, you lot tin have your friend let go.
- Be sure the tape volition hold the weight of the window before your friend releases it.

Advertising

1
Remove the window regulator bolts. The window regulator runs the width of the interior portion of the door and moves back and along in order to enhance and lower the window. Observe the bolts that concur the regulator to the door and remove them with a socket or open ended wrench.^[8]
- Set the bolts aside someplace safety, where you will hands be able to decide which bolts were for the regulator.
- Go out the regulator laying within the door's interior for now.
two
Locate and remove the window motor mounting bolts. The power window motor is much smaller than the regulator, but should be located shut by. In about applications, the bolts securing the motor to the door are the same size as the regulator mounting bolts. Remove them and set them someplace safe also.^[ix]
- Even if the bolts have the same size head, they may non exist the same length, so be certain to set them bated separately from the regulator mounting bolts.
3
Disconnect the motor wiring harness connector. The power window controls adhere to the motor and regulator via a wiring pigtail connector. Press the tab down to disconnect the pigtail and so pull them apart to disconnect the motor.^[x]
- Be conscientious not to break the tab that holds the wiring harness together.
- Pull the pigtail apart at the prune, non on the wires. Pulling on the wires could pull them out of the pigtail.
4
Remove the motor and regulator through the access port. With the pigtail asunder, the power window motor and regulator volition no longer be connected to anything within the door. Reach into the big access port and pull them each out.^[11]
- The two are connected, then pulling ane will remove them both.
- Be careful not to harm the regulator if you are only replacing the motor.
v
Connect the regulator to the new motor. If you are only replacing the ability window motor and not the regulator itself, you volition need to disconnect it and connect it to your new power window motor. Visually inspect the two to make sure the new motor matches the old one, then bandy the regulator.^[12]
- Different vehicles will use dissimilar methodology to secure the regulator to the window motor.
- Refer to the service manual for your vehicle if you are unsure of how to disconnect the regulator.

i
Slide the new motor and regulator dorsum into identify. Insert the power window motor and regulator back into the master service port in the door in exactly the opposite gild that you removed them in when disassembling the door.^[13]
- Orient each component so the holes for the mounting bolts will line upward with the holes in the interior of the door.
2
Supersede the mounting bolts. Hold each component in the advisable position as you return the mounting bolts that secure both the power window motor and the regulator. Thread each bolt in by hand commencement, then utilize a wrench to tighten them.^[14]
- If a bolt doesn't thread it properly, remove it and try again to prevent cross-threading them.
- The bolts don't have to exist extremely tight, just tight enough to prevent them from vibrating loose as you drive.
3
Reconnect the electrical connector. Once the power window motor and regulator are both mounted deeply to the door, connect the wiring from the motor to the pigtail you asunder previously. This will reconnect the power window switches and ability source.^[15]
- Exist certain the connections fit together. If not, you don't have the correct power window motor.
4
Remove the masking tape and lower the window back downward. Ask your friend to hold the window again. Once they are in place, remove the masking tape that is holding the window up in the door frame. In one case the tape is removed, your friend can lower the window dorsum into the mounting subclass.^[16]
- Make sure your friend has a grip on the window before removing the tape that secures information technology.
- Y'all can use adhesive remover like Goo Gone on the window if the tape left whatever residue once yous are done.
v
Insert the window mounting bolts. Have your friend hold the window in the correct identify so the holes in line up with the holes for the window mounting bolts. Once the window is in place, thread the window mounting bolts in by mitt, earlier tightening them with the wrench.^[17]
- Be certain your friend holds the window in place until the mounting bolts are in place.
- Have your friend let go gradually to ensure the bolts are belongings the window properly.
6
Reinstall the plastic liner and interior panel. Once the window is mounted again, you can reattach the plastic interior cover, so reinstall the interior panel over the door. Insert the door mounting bolts or snaps to hold it in place.^[18]
- Once the door is reassembled, reconnect the battery.
- First the engine and test the window.

Advert

Add together New Question

Question

If a regulator has a helper spring on it, exercise I need to take the whole regulator out to secure the artillery, or can I replace the motor while information technology is in the car?

Depending on the design of the vehicle, you will likely demand to remove the regulator as well as the motor when replacing it.
Question

Is the window regulator motor from a 2001 Ford Escape interchangeable with a 2002 Ford Explorer?

They might be. The best manner to know for certain is to check the part numbers for each and see if they match. If they do non, they are not interchangeable.
Question

Where is the fuse located?

The_general_s

Customs Answer

Fuses are normally in one of 3 areas: the engine bay, trunk area, near steering wheel.